Getting Ocean Ready

Just finished checking the rigging for the paravane pole and bird.

I’ve been ready to leave Vallejo for a month now. This is getting old. But I have vowed not to let myself be beat up any ore than usual.

I spent much of last week organizing parts. I thought I had only two types of hose clamps, stainless and non stainless, which I separated last year.  If only life would be so easy.

As you can see from the attached picture, I have essentially 7 different stainless-steel hose clamps and guess what, that large bunch in the back of the organizer all have stainless bands, but non stainless screws! That’s totally worthless. I wish I could be sure that that bunch was not Made in America!

My 7 types of hose clamps

And they are also organized now by the size of the screw: 5mm, ¼”, 6mm, 7mm, 8mm. this allows me to easily use the same size for any particular job, as opposed to discovering that the dual clamped sanitary hoses have two different sizes of nuts.

I’m now doing things that were not on the list, like measuring the paravane bird rigging.  When we left Martinique, 5,000 miles ago, I had the birds set to run 19 feet below the water surface. that’s 5 feet deeper than previously, as I finally realized that in larger seas, waves greater than 10 feet, the bird itself was being picked up in the rotor of the wave, negating much of its effect.

Stbd paravane pole with double loop proving a quick extra 10 feet of depth should conditions require it.

Since Martinique all has been good on that front.  Now, I made sure of the depth and also marked the poles. In addition, I re-rigged the extra line, so that I can quickly run then 10 feet deeper if the situation, really large seas, warrant it, without stopping or even slowing down.  With the re-rigging, I just have to take out a few clove hitches and the extra 10 feet is free.

Here is also a before and after picture of the driving lights. They are handy when anchoring in strange spots with other boats or mooring buoys around. I’ve also used them in dark, narrow, lonely channels. T

here have been a few too many of those.

My long term filter carton is a bit depleted. I have already taken out my last 6 Racor 2010 filters. I keep them in the engine room by the Racors..
I have only half a dozen Racor 2050 filters left for my fuel polisher, as well as a number of engine mounted filters, along with some water sediment filters for the water maker.
Driving lights off

 

Driving lights on.
I only use them for anchoring in unknown places or in narrow, but marked channels.

Chasing Screws

I’ve been ready to leave Vallejo for a couple of weeks. But the winds off the northern California coast are proving to be more persistent than the northerly winds off the Mexican coast last year. There is a blocking high pressure area in the eastern Pacific that just won’t leave. It’s certainly been there almost all spring. Doesn’t it realize summer is almost here?

One of the other manifestations of this weather pattern is the north east has been cooler than normal.  Let New York have the brutal hot and humid conditions they are used to and let me have gentle breezes.

This is all stainless except for that compartment of brass screws on the right. I’m holding a 1 Kroner Norwegian coin. It has a hole in it and is not magnetic, so it goes with the washers.

So, in the meantime, I am organizing.

I had wanted to put off this tool and parts re-organization until this summer when Ti and Thien are with me. I had thought that it would be a good way for them to understand what things are, where they go and how we use them.

Oh well, the best laid plans of mice and men, sometimes go astray.

During the last two months as I have worked on various projects on Dauntless, countless jobs have taken longer than they should because I can’t find the right tool or part. Admittedly, it doesn’t help that I have spent 20 minutes looking for a flashlight that I could not find because it was ON and my brain was not looking for something that was lite, no matter how obvious.

I have also spent 15 minutes looking all over the boat, for a part I had just found only to have placed it someplace. 15 minutes!  I knew I had put it someplace I wouldn’t lose it. Where was it? In my left hand!!

Talk about the right hand not knowing what the left hand is doing!

Crescent wrenches and sockets

So, a re-organization is necessary. I mentioned before that I had mixed stainless-steel bolts and screws with non-stainless. But I discovered I did not just have one tray organizer like that, but three or four.  I also found fasteners that I thought I had but couldn’t find.

Now, everything is in its right place.

I also had the problem of finding four 13 mm wrenches, but not the one 14 mm I was looking for. Now, I have a full set hanging in the engine room (before I just had the 13, 14, 19, and large adjustable that I needed for the fuel filters).

Tomorrow, I’ll tackle my electric parts. I know I have a lot, 220 v, 110 v, 12 v, but the 5 or 6 containers I thought I had has grown to more than a dozen.

 

 

Almost Done

I had hoped to leave Vallejo for my trip north as early as a week ago. It wasn’t to be and with the eastern Pacific high showing signs that it doesn’t know that summer is here, I doubt I will leave before mid-month!

Dauntless’ Fly Bridge

Talking with a boating friend Friday who is very attuned to the weather in Northern California, he told me that normally, this eastern Pacific high is strongest in April, when it produces the strongest Northerly winds. But it’s now June and the April high is still here.

As a weather forecaster, the shoulder of the seasons, spring becoming summer, etc. is the hardest thing to predict. Each season has its own peculiarities, as well as the type and strength of the weather produced.

One crosses the North Atlantic in July because that’s definitely summer. Low pressure areas in the North Atlantic in July are the fewest and weakest of the year. Winds are almost never above 50 knots. When I was planning my first Atlantic Crossing, that’s why our planned departure was in July. June and August are the shoulder months, August weather can quickly transition to fall. Two sailboats were abandoned off the coast of France in a May storm, a few years ago.  That I found myself in the North Atlantic in late August is a story I have related a number of times. Needless to say, the weather was worse than the month before and the successive three lows that rolled over me during my last 72 hours were definitely a sign of fall type weather; summer was over.

Dauntless’ Fly Bridge

Now, I’m waiting for spring to end. In the meantime, having gotten almost all my projects done, I am now cleaning up the small things.

My fly bridge has never looked so good. All my mild steel items, cotter pins, bolts, nuts, have been replaced with stainless steel. In the past, I used what was handy. During the last couple of months, I have spent days removing rusted fasteners or clevis pins that are ruined because they have a rusted cotter pin inside.

Lesson Learned.

I also added a line of lights for the galley and added a lighted led switch that purposely stays on all the time. I figured people new to the boat, Ti and Thien in particular, would appreciate some help in finding lights and things.

Blue Led switch is middle right just below the cabinets
Dauntless’ solar panels

Over the next days, I am reorganizing my tools once again, as well as much used electrical parts.

Here is the latest snapshot of the weather patterns and winds over the North Pacific. First picture is today, the second picture is June 11th. No point in looking at anything else.

In the meantime, here is an interesting link to the video Ti made, Ti Cooks Pig Ears. with English subtitles. Yes, another Vietnamese delicacy. Who knew they did more than Bahn Mi sandwiches and Pho !!

 

North Pacific Weather Patterns Valid 02 June
North Pacific Weather pattern valid 11 June