On a Roll

Yesterday, I completed two things on the nice to do list: replacement of the Raritan water heater anode and replacement of a terminal block for my 120-volt neutral circuits in the engine room distribution panel.

The new anode is on the right

After two months, I’ve finally hit my stride and actually feel confident in what I am doing. That manifested itself in those two completions yesterday. Instead of taking a couple of days, they took a couple of hours and I didn’t have to redo anything.

This got me to thinking about a job interview I had just the other day.  I found myself talking about the importance of not overwhelming students, especially students who may be far being in whatever work that needs to be done.

I mentioned in the interview that even when a student was far behind, let’s say they need to complete 20 projects or work assignments by years’ end. It’s already February and they have nothing done, with only a few months to go. It’s easy for a teacher to just be upfront about it, if you don’t get these done; you’ll fail.

I’ve seen teachers do that countless times. But it won’t accomplish the stated goal of getting that student to be successful, (though it does make the class smaller). If a student sees a mountain of work to do, they never get started, discouraged, not seeing how they can get it all done, they give up before they even start.

That’s me, now and then.

My driving lights are lighting up that sailboat

So, two months ago, when I made my list of the top half dozen things to get done before departure, I knew the last was far bigger, but I couldn’t overwhelm myself. I didn’t want to paralyze myself with indecision. Now, I know many of the readers here are successful boaters because they just see what needs to be done and get to doing it.

In the same way half of all students are impervious to the adults in their lives who get in their way, be it parents, teachers, or anyone else. They’re going to learn and be successful no matter what.  It’s not by chance that the historic graduation rate in the last 50 years continues to be about 50 to 60%.

I’m not in the group. I needed a teacher to be able to at least steer me in the right direction or a teacher who could tell I was bored to death and challenge me in ways the curriculum didn’t. The same way a good teacher will give make-up work to a student in a piecemeal fashion. Do this for me tonight and I’ll give you something else tomorrow. At the same time scaffolding the rigor of the work. So, in a short time, they are whipping out stuff they never thought they could do just weeks ago.

Two months ago, starting with a list of 6 items, I knew I’d do more. I’ve done three times that amount so far. While moving the instruments on the mast, I knew to check the paravane fittings. The clevis pins needed to be checked and I wanted new cotter pins. I also noticed too much wear on the main fitting to the mast, so I needed to add some washers and new pins.

As I did more and more, sometimes taking a week to complete one checklist item, but I also did another half dozen items, that were not on the checklist.  I became more confident.

Confidence is the other side of the equation. When I finally completed the LED project, which involved 4 wires, with four conductors each (a positive, and 3 separate grounds that control the three colors, blue, red and green), I was very pleased to see it all worked as anticipated. I had three switches to turn each respective set on or off, plus three additional switches to control the colors, since I figured I didn’t need any complicated controller.

That it all worked, gave me the confidence to tackle the 120v terminal bar, that seemed straight forward, but you never know. When that went well, without me having to redo stuff, I tackled the water heater anode and that went even quicker.

The order I tackled these projects mattered. I have read education studies that when formulating a test, the order of the questions can make a significant difference.  The same questions in a different order can make a significant difference in student performance. Teachers have known this forever. If you put the hardest questions first, it discourages students. Why a teacher would do that is a story I will save for the book I’m thinking about writing. But it also goes to our overall 60% graduation rate.

When I took the test for my NMC Master’s license, the lights and signals test was the hardest for me. It was hard enough to remember red over green. Was that fishing or trawling or neither? But the day shapes were even harder for me, since I was not using them myself.

For a week I took practice tests. The passing requirement for that portion of the test was the highest at 93+%; meaning out of 33 questions, you could only get 2 wrong.

During my practice tests, I got anywhere from 65 to 80% correct. Well off the mark.

Test day came up and we took the other three portions of the test first that were easy for me. Then the dreaded lights and signals. The first 5 or 6 questions were “easy” in that I was sure of the answers. By the end of those 33 questions, I was positive that I missed only one!

Well, I missed two, but that was still enough to pass. I was elated, but I also recognized that the question order made a significant difference for me that day. Because I felt confident in those first half dozen questions, I didn’t stress and overthink the rest.

In the same vein, when I started working on the boat projects, I knew the order made a difference.

Since I whizzed through those two things yesterday, I decided today to tackle the Purisan project. Two months ago, I’d not even mentioned it because …

But now, it’s almost done, but that’s for tomorrow’s story.

 

 

What’s Done So Far

I think it was time for anew anode for the Rartitan Water Heater

Slowly, but surely progress is being made.

I have completed the following:

  1. Installation of outside LED rows and inside wiring, Amazon LED Link

    The drving Lights on new brace with new brackets
  2. Added another power line for the pilot house electrical panel and also added an additional ground,
  3. Replaced the terminal block for the 120v system neutrals in the engine room distribution panel,
  4. Replaced the anode for the Raritan water heater that I didn’t know existed until a few weeks ago,
  5. Replaced the brackets for the three driving lights and replaced the two fog lights with stainless steel brackets I had made in Vietnam,

    The fog lights are pointed down: to see the chain coming up and to make the boat more visible by lighting the hull, if I’m anchored in a busy area.
  6. Tightened the thru bolts for the paravane pole brackets; replaced all the cotter and clevis pins with new stainless steel.

    Closeup of the double row LEDs in the clear rubber jacket that makes them truly waterproof (we’ll see)
  7. installed a set of fog lights to the spreaders,
  8. Moved my Maretron weather instruments, GPS and my Groove WiFi extender to the spreaders on the mast,
    The old terminal bar
    LEDs as blue

    The LED lights white. Can also be red, green or blue
  9. Repaired (at the last minute before replacement) my 12v heating pad for my bed that is 5 years old and stopped working a month ago. Just before I went to buy anew one, I decided to have one more go at fixing it. I did.
    My reward
    The aft deck lit by the LEDS

    The new terminal bar at the bottom of the picture

I’m treating myself to rack of lamb today.

Stay tuned.

Two Steps Forward, a Couple Back

Why couldn’t I just say Two Forward and Two Back?

My New Fresh Tank Selector Valve to the left of the stairs

The words: a couple, a few, came in handy back in 2004 when I had to teach significant digits to my high school physics class.

While I’m pretty good in physics, meteorology really just being mostly math and physics, with a few fluid dynamics classes thrown in, I had to refresh myself (learn) about significant digits to teach it. As it turned out, it was the last year in was in the New York State high school physics curriculum, but I thought it important, so I taught it.

At the time I wondered why I didn’t it didn’t come quickly to mind as the other important concepts of physics did. Later, I realized because during my high school and university, I was using a slide rule and understanding how many digits were significant in any calculation was an integral part of it’s effective use.

Thus, I “knew” it, without knowing what I knew.

So, when thinking about this blog post today, I debated titles: Two steps forward, three back, no, I have made some progress, two forward one back, let’s not get carried away on the amount of progress, two steps forward, one and a half back, sounds awkward.

My New Fresh Tank Selector Valve with the stairs. The grey box on the bottom middle is my bus heater that really warms the boat when underway)

Two Steps Forward, a Couple Back about sums it up. Of my 6-item list I of last week, one, moving the fresh water selector valve is done, but now instead of 5 things left to do, I’ve already discovered a dozen more. I’ve already taken care of a few, like the hole I found in my stainless-steel sink (how does that happen??), but that still leaves me with half-a-dozen more.

Therefore, the ambiguity of “a couple” is perfect.

My re-positioning of the fresh water tank selector valve is done. Finally, with only a few missteps. In the process, I may also have found the problem with my fresh water pump. I had to replace the pressure switch back in the fall and at first, I taught all was OK, but then I noticed decreasing water pressure as the pump ran. For most of the winter, I assumed I had to adjust the pressure switch, but now I think I had a very small air leak in one of my older water hoses where it connected to the copper hose (and I put new hose from the output of the selector valve to that copper fitting).

I’ll know once everything is up and running and no matter where you live you will probably hear me laughing or crying in my shower depending upon the outcome.

I’ve also been working on a number of electrical/mechanical improvements:

Maretron intruments now on the spreader of the laid down mast
  • Repositioning the Maretron instruments on my mast, including running a new Maretron cable and re-conditioning all the connectors,
  • Moving my Groove Wi-fi extender to the mast also and running its antenna cable thru a new route from fly bridge to pilot house, as the old wire race is full to capacity.
  • Adding switches, replacing a fuse box, adding a voltmeter and rewriting my AM/FF radio in the salon.
  • Adding some LED lighting to the side decks (more robust and waterproof than my initial effort 5 years ago.

Pictures and results to follow.

My New Fresh Tank Selector Valve with the stairs. The grey box on the bottom middle is my bus heater that really warms the boat when underway.

Moving the mast instruments has been a drama. After finally realizing I needed to tap and die the bolts for the spreader since the aluminum is so thick, 3/16th, to ¼”, I was “pleased” to discover that while I have two metric tap and die kits, I have virtually no metric bolts or machine screws, at least none that were stainless steel.

My Tap and Die kit and the metric machine bolt assortment from Amazon.

So, I spent some days, just sorting my stainless steel and figuring out what was metric and what wasn’t. It’s amazing the amount of stuff I’ve accumulated that really isn’t suited for boat life, but I don’t want to get rid of any of it, because you never know what you may need in the middle of the ocean.

Having said that, it’s so strange to get my mind around that fact that for the foreseeable future I will be in range of Boat US or Sea Tow.  More so because in my first year, going up and down the ICW, I had Boat US on speed dial. But now, having spent so much time and miles being totally independent, it’s a mindset that is not easily turned off.

Now for those of still waiting anticipation of learning about significant digits.

It means that no matter how many digits your calculator displays, you need to use your common sense.

e.g. I walked 2 miles (a couple) today. There are 5280 feet in a mile, therefore, my calculator tells me I walked 10,560 feet.  But did I walk exactly two miles? Or was it 2.1 or 1.8 mile, one cannot know from the information

I love these warm, non slip socks. Pamisi on Amazon.

given.

5280 has 3 significant digits, 2 has 1 significant digit, when multiplied you take the minimum, therefore the answer will have one significant digit. So, even though the calculator says 10,560 feet, the answer with significant digits in mind is 10,000 feet (rounded off to the one significant digit).

You can get a very nice definition and explanation here:

http://limestone.k12.il.us/teachers/rhebron/Chem_HO/c05_Sig_Figs_Help.html

 

 

Work on the Mast

During the last week on Dauntless, getting her ready for the winter without me, tears all around, I realized how sweet it was to work under a roof. 

Looking aft with the mast down, under the roof of the Vallejo City Marina

I loved it so much, I changed my project priorities a bit.  I figured it made the most sense to do those things that are difficult to do under normal circumstances.  It is such a pleasure to sit on the fly bridge, out of the hot blazing sun or the cold wet rain. With the mast down, I didn’t have to wrap one arm around the mast and hold on for dear life. Under such ideal conditions, I realized I had to get all the things done I had been contemplating for years.

Four years ago, getting Dauntless ready for her first ocean crossing, I took what was given. Unlike the Lexan storm windows which were done in the last hours, the Maretron system and instruments on the mast were completed with days to spare.

One thing that has sunk into my dense brain is if I don’t have a clue as to what I am doing, then at least do the simple solutions instead of making complicated ones. To that end, I mounted the Maretron instruments on an existing antenna arch that extended forward and was above the radar.

It was the simplest solution and worked well enough for four years, but now, I wanted to make it better. I have felt that the weather instrument that measures all the normal weather parameters, including wind speed and direction, is not in a clear air stream with winds from the stern. As you know, this Kadey Krogen loves following winds and seas, therefore if the data is being affected under such conditions, it’s not ideal.

The other issue that is also related to stern winds is that every once in a while, lines related to the paravanes, get enough slack that over time, being blown forward, like 21 days in following winds and seas, that they were easily snagged on those weather instruments or the bracket itself. In the first years, more than once, after deploying the paravanes, I discovered that the weather instrument arch was carrying the weight of the paravanes. Not good. (Though it does confirm the forces on the paravane system are as expected).

Just too many times, that antenna arch has been seconds from disaster. Time to get rid of it. The Maretron cable that runs inside the mast must also be replaced. So, the Maretron WSO and GPS will be mounted on the spreaders. In addition, I will mount my Wi-Fi extender antenna and I hope to also move my current AIS antenna to the spreader. Currently it’s mounted on the cowling of the fly bridge near the helm. It’s too low. Many times, it will not see big ships until 5 or 6 miles away. At the Dauntless speed of 6 knots and big ships possible speed of 20 knots, that still gives me more than a 10-minute warning, but that antenna should be maximized just on principal.

Plan for the Mast Spreaders
March 2019

I also need to remount the two Chinese LED spreader lights. The lights themselves, bought 5 years ago on Amazon for $20 each, have been great, but the mounting hardware is mild steel that rusts badly. I have a way to mount them directly to the spreaders, without the steel hardware. Since I am doing that, I will also change the electrics a bit and add an electrical circuit to power a LED stripe that I will also mount on the mast.

Now, your thinking, while I have eliminated one protuberance, I have made the spreaders much more complicated. That’s true. But I have a plan.

I will also add a 1/16th Amsteel line from the top of the mast to the end of each spreader, then forward to the front of the radar arch. Looking aft from the bow, this will look like a triangle. Looking from either side, this will look almost like an obtuse triangle.

Now, I have not added this yet. This will happen in March when I return to Dauntless, but in my mind’s eye, I see this little line as making it much more difficult for a loop of any line to become snagged around the spreaders, radar arch or the mast itself.

We’ll see.

 

Maretron or Not

For a little, non-electronic boat, I sure love my Maretron data. I have 9 modules:

  • two to communicate with everything else, (USB, IPG) and the N2K Viewer
  • two for the fresh water tanks, (TLM),
  • one solid state compass, (SSC),
  • one GPS, (GPS),
  • one depth sounder with paddle wheel and lastly, (DST),
  • the love of my life, my (WSO), the weather instrument.

The solid sate compass seems to work better with my ComNav autopilot. In addition, it gives me the roll and pitch data I often quote in my blog.

The weather instrument is also solid state with ultrasonic wind measurement.  Considering I installed the system myself over 4 years and 20,000 miles ago, I’ve had few problems.

A glorious day in Vallejo, under a roof, with the mast down, facing aft

Coming west across the Atlantic, the constant winds behind us and to the side, from 15 to 35 knots for 528 hours or 22 days (No, I didn’t stop to change the oil) took a toll on my connections on the mast. Everything still worked, but occasionally, if a line got caught it would put enough strain to disrupt the connection until I freed it.

So, one of my projects now is to redo all the connections in the system. I  also now slather everything in dielectric grease. So much so, that I almost put it on my pancakes the other morning.

One of the offending connectors

So, the day started out so very well. Sitting on deck, with the mast down, Dauntless under a roof, protecting us from the elements and sun, I thought about climbing up the mast in Cabo San Lucas, in hot, 95° sun, holding on the mast with one hand, while trying to tighten the 5 little wires inside the plug just under the WSO.

I was in hog heaven. I carefully tool the plug apart, unattached the 5 little wires, and recut them all and trimmed them. Now, I knew power was still on the system.  Before I started any of this, I wanted to make sure that it was only the WSO that was incommunicado.  So, just as I was thinking that I would have to be careful in cutting the positive power line, meaning not to cut it with the ground wire at the SAME time; I did exactly that. The little spark, showed me that I’d f..ed up.

Sure enough, when I go below to check, now the whole Maretron system has no data.

Had I shorted out something serious? Was there a fuse in the system? If so, where was it?? Who the hell installed this system?? Oh, it was me!

Let me check the computer cabinet. Open cabinet and what do I see, the fuse block that I put in 4 years ago and even nicely labeled at that.

It went downhill from there.

To check the fuses, I had to pull them, to do that I needed to power down the whole system. That done, I pulled each fuse and looked at it very carefully. Very carefully (for those of you who already know the answer, don’t spoil it for your dear ones who are also reading this).

They all looked good. I powered the system back up. That takes a few minutes because the modem and router have to be booted up before the computer otherwise everyone gets confused.

At this point, I noticed that the little light for the Maretron circuit was not lit on the router until I turned on the computer. I hadn’t noticed that before. (and in the future, I will explain that issue).

No change. I went back to the fly bridge. One of dozens of trips I would make over the next couple of hours. I figured I had screwed up the wiring of the plug. I took it all apart again. I convinced myself that possibly the ground shield covering was touching one of the data lines. I put it all back together again, rebooted the entire system and alas. No joy.

At this point, I’d spent an hour on this. I pulled the fuses again. They still looked good. I even held them up to the light. But finally, just to be sure, I changed the 5-amp fuse that powered the Maretron system. Surely now, it would work.

Still No Joy. Now, more than ever I was convinced it was the plug. The plug was the only thing I had worked on.

Back to the flybridge. Took plug apart again. Put it back together again. Rinse and repeat.

I got my electric meter out (finally you think), check the plug for the umpteenth time. No power.

I go online and check the Maretron site. It tells me I should see 60 and 120 ohms between certain lines. I see exactly that. But still no power. I must have shorted something else out. Where did I install the power tap?

Oh, I remembered where the power tap was because it’s in the port side pilot house wire race that is so full of wires I have trouble getting the teak panel back in place.

Other than no power, the continuity on the plug and lines tested correctly.

I’ve been working on this for three hours now. I return to the computer and fuse block.

I finally decide to test for power in the fuse block. Umm, the Maretron circuit has no power here.

I pull that fuse and check it. No circuit. I check the old fuse I had pulled out, no circuit.

I got fuse number three and checked it, a circuit.

I stick it in and low and behold, power.

Two hours earlier I had replaced a bad fuse with another bad fuse. Both fuses showed no sign that they were open. Both had very clear “Z” wire that wasn’t broken.

One of the offending fuses

 

The Dauntless Winter Home

CE Chart showing my route from Santa Cruz to Vallejo. Maretron data shows winds, and other environmental parameters

Passing under the Golden Gate, I felt the chapter coming to the end. Like turning the page and seeing only a short paragraph remaining.

As I made my course eastward under the bridge, the winds picked up as forecast to westerly at 20 to 25 knots. I was happy to have just gotten up the coast before the band of strong northwesterly winds had reasserted itself.

I also knew now that no matter what the winds did, my ride to Vallejo would be relatively smooth and it was. The picture shows the Maretron data with winds as high as 32 knots, but the roll reduced over what it was on the ocean.

After a few hours of motoring up the channel, Fly Wright was there to greet me.

Fly Wright meets us

I had to dock outside my covered slip that first night, as I had to lower the mast and the paravane poles.

With many hands helping, the mast the poles were easy to lower, though I wondered how I managed to do it myself a few times.

We had a great dinner that evening at the Sardine Can, a good restaurant near my slip. The next day, I moved Dauntless to her winter home. She’ll be there, out of the sun and rain until next spring, when we continue our northward trek.

The winds were blowing

This time I remembered to change the oil right away. I also had a long list of items to do before I flew away.

My winter Home Maretron Data shows the summary of the previous two days coming up the coast from Morro Bay.

I’ll be back to her in September to commence a long list of projects that hopefully will be done by spring.

 

 

The Golden Gate

On the 63rd day since getting underway from Huatulco, 2300 hard miles ago, I got up for the last day at 02:00.

The Golden Gate Bridge dead ahead

70 gallons of fuel would be more than enough to get Dauntless the last leg to San Francisco Bay and Vallejo.

Checking the current tables, I had to get to the Golden Gate by 13:00. Then the current would push me the last 40 miles to Vallejo at plus 2 or 3 knots. To make that happen, I had to depart by 03:00, planning 10 hours for that 65 nm.

02:33 Engine start. We (Dauntless and I) were underway at 02:45, with scattered clouds and southerly winds.

I had about an hour of cruising WSW, before I could head NW. After a few hours, just after sunrise, I was able to go on my final course of 340°. The winds stayed southerly at 12 to 16 knots for the rest of the morning. Just enough time for me to get into San Francisco Bay.

Videos I took that morning: 

A brown day with wild fire smoke

At noon, 12:00, I was entering the Golden Gate channel. My goal of the last 10 months was in sight.

Leaving Santa Cruz Channel

And it was an impressive sight. To be looking at the Golden Gate Bridge from the Pacific on my own bottom. How many people can say that?

I was proud: of my accomplishments, of my determination to complete these goals, of this Kadey Krogen that was so strongly and safely built.

We could not have come up with a better name, Dauntless, determined, never give up.

First Glimpses

 

All of the pictures  Dauntless moving north from Mexico to California 2018 can be seen here in ascending chronological order. Please note that most pictures have the date and time they were taken in the picture/file name.

All the Dauntless directories are here, Dauntless Pictures

 

With My Heart Still Racing

I still needed to get Dauntless out of this harbor safely.

Leaving Morro Bay at 01:42
Dauntless is near the top of the horseshoe on the CE, C-Map chart. From left to right: Raymarine E-80 radar, probably set at 1/8 mile, Samsung LCD 24″ monitor showing Coastal Explorer C-Map, below, Samsung 12″ tablet showing Navionics chart. .

After a close call, like I just had, it’s easy to relax your guard, but it’s still dark, in a narrow channel lined with boats, piers, infrastructure and even sleeping otters.

For 30 minutes I threaded my way thru the horseshoe shaped channel.

At exactly 02:00 I passed the outer marker and set my course to the northwest. ETA to Santa Cruz marina was 19:00

Video of us leaving Morro Bay:

I took a few deep breaths, regretting that that I didn’t have a sheep, goat, first born son or even a chicken to sacrifice to Poseidon.  Did a few Hail Mary’s and settled in for the rest of the night?

Windy.com had depicted a very narrow inverted trough moving off the coast during this 36-hour period. What that meant was that now, 02:00, winds were light from the land (the nightly land breeze) but would strengthen rapidly during the early morning hours. Then stay strong, 20+ knots out of the south for the next 24 hours, before the dominant high-pressure system, which had dominated the weather in the eastern Pacific for like forever, or much of the spring and summer so far, would bring back the strong northerly winds.

This meant I had until noon the following day to get thru the Golden Gate. After that, winds would be 20+ from the north.

I kept the rpms up, 1700, boat speed varied between 6.3 to 7.3 knots due to the coastal current. With no current, the speed should have been about 7 to 7.2 knots at 1700 rpms.

Pitch and roll were ok, pitch was a few degrees up and down, roll +5° to-8°, the Krogen had an easy motion. There was a swell from the NW at 4 to 8 feet and wind waves from the SE at 1 to 3 feet.

It felt so good to have the wind behind me. I could open the pilot house door without the fear of the wind grabbing it from my hand. I could stand there and just watch the ocean and the sky. I love the ocean as a fish loves water.

By noon, winds had picked up to 15 knots, still from the SE. I estimated the NW swell now at 8 to 10 feet. (which meant my earlier estimate of 4 to 8’, made in the dark, was probably understated).

Video of us underway at 13:22:

By 14:00 the winds had increased from the south and were now, 180° at 19 gusts to 25 knots. Pitch and roll had doubled: pitch was +4°/-8° & roll +11°/-11°.  That roll was at a point I would deploy the paravane stabilizers, however in this instance two factors mitigated against it:

  1. It would take a knot off my speed and
  2. I had just passed many fishing boats. I got tired of fishing trawlers buzzing me because they thought I was stealing their fish. In the heavily regulated fishing industry in the USA, it’s not as much of a problem, but I’d just spent 4 years outside the USA.

At 19:00 I entered Santa Cruz harbor.  Was tied up at 19:19.

We did 121 nm, 17 hrs:42 min, at an average speed of 6.84 knots.

I had a nice dinner with my new-found cruising friends, Ralph and Kristen.

By 21:00 I was tucked into bed, with the alarm set for 02:00 and my last day of the 2018 Baja Bash.

The last day of June ended with a whimper.

All’s Well that Ends Well.

 

 

 

 

 

 

 

 

 

Seconds from Disaster

A long, harrowing day was over. A good night’s sleep erased much of the drama. I was closer and closer to the end of this Baja bash.

07:25 I get up

07:30 I did my morning checks and log entries:

  • Fuel: 3.25” port; 5.5” stbd
  • Batts: Current draw -8 amps, 12.48v, -84 amp-hrs.
  • H2O: 72-gal port, 82 gal stbd, feed stbd
  • Oil: right on the full line
  • ATF: 1 bar down, NC (Since I was still losing ATF, I checked this, normally I don’t)

07:53 Engine start, 6625.88 engine hours; Systems all Go.

07:58 Haul anchor

08:08 Anchor secured.

08:10 Underway to Morro Bay, following the track I came in on.

08:15 Do weather observation: Overcast Stratus Strata cu, Vis 2 miles fog, 1017mb 55° 51° 49° (sea temp) winds 27005

08:42 1700 rpms, 6.8 kts, slow to 1600, 6.4 kts, 1-2 ft swell on bow, larger swell 3-5 ft n bow. Pitch +4°/-4° Roll +6°/-3° benign.

09:25 1600, 6.5 kts, course 293°T, winds 27007 Pitch increased to +8/-8°

10:22 Change course to 016°, 1600 rpms, 6.2 kts, 3.5 nm to Morro Bay entrance. 7 knot winds on beam are producing a lazy roll of +10° (to stbd)/to -05° (to port).

11:30 Enter Morro Bay. Spot my first Sea Otters. Great.  One more thing not to run over besides the ubiquitous paddle board and kayak people.

Sea Otters of Morro Bay

12:03 With a slow, almost idle, 4 kt approach (The minimum speed to have enough way to control boat), I approach the Morro Bay Yacht Club dock. It parallels the coast and there is ample room for me. I make a 180° to port (the direction this KK loves to turn) and am tied to the dock minutes later.

12:05 Docked at MBYC. An easy day, 3:55, 23 nm, 5.9 avg speed.

Arrival track is good. Departure is Garmin.
If you go to Share.Delorme. com/Dauntelss by clicking on the dot it gives you the speed, time and location, but times look converted. Thanks to Google, Garmin or Windows.

Morro Bay turned out to be a delight. Delightful people at the delightful Morro Bay Yacht Club (MBYC). If I was ever in one place long enough to join a yacht club, MBYC would be the kind of place I’d love to join.  Having to wait out the weather for four days turned out nice. Really reasonably priced at $35 per day, it was a pleasure to be there. I felt good and knew that time wise, I’d be good to go if I could leave on the 30th.

Morro Bay Yacht Club hamburger night
Dauntless in front of the MBYC

I watched the winds every day and the forecasts were tracking well. I thought to leave Friday, but the winds were still up and while forecast to go down later in the day, this is a perfect example of when I say, “Don’t leave based on a forecast”. If your waiting for light winds, wait until you see light winds.

Also, MBYC had hamburger night Friday evening or maybe it was cocktail hour. In any case, I vowed to leave early Saturday morning, if winds were light as predicted.

Now the plan was getting down to hours. The anticipated 36-hour weather window showed light winds becoming increasing strong, but from the south as Saturday progressed into Sunday, but by Sunday afternoon, the northerlies would be back with a vengeance, 30+ knots west of the Golden Gate.

Additionally, the trip up San Francisco Bay must be timed for the currents and tides. The currents are as strong as hell’s Gate in NYC. So, I had to back up all my arrivals and departures so that I would arrive at the Golden Gate between 12:00 and 13:00 Sunday July 1st.

To get there at that time, I had to leave Santa Cruz before 03:00. So, if I wanted 5 hours sleep in Santa Cruz and a time to have dinner with some new boat friends who had their boat there, I had to leave MBYC at 01:00 to do the 121-mile trip in 18 hours, getting me to Santa Cruz by 18+1= 19:00

No problem. Just an early evening and get up at 01:00.

this picture was taken just 5 hours before my departure. I was so enamored with the sunset that I really did not look at the situation.
Notice the solar panel array on the port side stern of the sail boat in front of me.

Dauntless was parallel parked between two sailboats. The evening before I had asked about leaving that early, anything I needed to know. Everything seemed routine. I should be able to just push the bow out as I realized the last lines.

Maybe the sailors giving me this advice did not realize that Dauntless was 44,000 pounds? Certainly no one warned me about the current.

01:15 up, Saturday morning dawned with the expected light winds, I was ready to go.

01:20 As I did my routine combined current check and pee, it was obvious that the current was not insignificant.

The next 8 minutes were the most harrowing of the last three months.

It was obvious I couldn’t just undo the lines and push her out away from the dock and SV 15’ in front. Plan A was dead.

The stupid sailboat in front of me has two solar panels out behind his stern. On the first picture of this post, the sunset, the solar panel array is visible on the port side stern of the sail boat in front of me. They are probably 12 to 15 feet from my bow pulpit, which is 5 feet above them. But my hull will impact them before it hits anything else. No fender could protect them. This guy should be on a mooring.

Plan B: I untied all lines, but for the midship cleat. I wrapped it around the dock cleat near the stern, so it would slide thru once I released tension on my side. Meaning the line was secured to the boats stbd midship cleat, then back to the stern cleat on the dock and then I’m holding the bitter end in my hand while on the dock, near the pilot house door. The boat is in neutral at idle. For this to work, my plan is to give the bow a mighty push from the dock, releasing the line while I clamber on board.

With one mighty heave, I was truly seconds from disaster.

Dauntless was not moving out as much as I had hoped. I also was keenly aware that I was risking her leaving without me.

I clambered on board, as dauntless drifted forward crab like, her bow maybe 15 feet from the dock, stern still near the dock. I debated momentarily, for a split second at most, whether to just give her a shot of power, hoping that she would go straight out into the channel.

At 1.5 knots, that about 2 feet per second. In the 6 seconds it took me from release of the line, get on board and into pilot house, Dauntless moved 12 to 15 feet, the bow pulpit was almost over the left side of the sailboat. The stupid solar panels are a few feet from my stbd hull.

It was clear to me in a moment that if I gave it forward power, it would rake the entire starboard side of Dauntless against the stern port quarter of the SV.

I quickly put her in reverse and slightly increased power to 1100. I also had a sailboat behind me. I ran out to the bow, just in time to find off the stupid solar panels as the Kadey Krogen finally started to retreat.

I ran to the side deck to see what kind of room I now had behind me. I need to be tied to the dock I bought myself some more seconds by leaving her at idle in reverse. This gave me enough time to get to the side deck and get a line on the dock cleat. I made it tight and thought about what to do.

I took some needed breaths. I had to be calm now What were my options? It’s almost 1:30 in the morning. No one is getting up soon. On one hand it’s only a schedule, but being alone, makes the schedule even more important. If I didn’t leave now, I would be forced to run overnight. Which then has an impact the following day.

The Golden Gate timing was immutable.

I wanted to leave, but the idea that I start me day be destroying this boat’s solar panels would really fuck up my day.

I tied the boat thru the stern cleat to the dock’s cleat just a couple feet away.

I would try to push the bow out with the stern tied. I wouldn’t do anything else. Engine at idle, transmission neutral.  It was just an experiment to see how far the bow would actually go out. If it went out to 45°, It would probably work.

It went to maybe 20°.

Tied again with a little more slack on the stern line, same results, but now she headed for those f…ing solar panels again like they were a magnet.

I had some seconds to spare this time, but I had to get her in reverse. We were still attached to the stern dock cleat. I had tied it so that while in reverse it did not have enough slack to hit the boat behind me. In other words, while I could watch the bow, I had to make sure when backing not to hit the boat just behind me.

Then I noticed an interesting phenomenon in reverse, attached to the stern cleat, the bow came out.!

That made perfect sense since Dauntless stern always wants to starboard. I need 2° of right rudder to go straight. In reverse, the prop walk is still to the right, to starboard, which is pone of the primary reasons, I always try to dock and tie on the starboard side.

(which in a recently found video has me backing into the slip in Golfito, Costa Rica. Once I figure out how to get it not inverted I will upload)

I checked the line on the dock and boat to make sure they were secure and then gave her more power in reverse. The bow keeps coming out more and more. This would work.

Back to idle, I quickly retied the stern line so that the closed loop was over the forward horn of the cleat. I then ran the line thru the stern hawse pipe forward inside the boat to the midships cleat.

I put the boat in reverse and added some power.

The bow came out further and further. Still in reverse, I sent down to the midships cleat, and took the line in my hand and walked it back to the pilot house door. With the line in my hand, I checked the port side to make sure it was still clear, gave her more power and the bow came well out.

Now, I knew the terrible downside of this plan. If that dock line snagged on something, at best it would slam the boat back to the dock hitting the boat ahead, at worse, I could drip the whole dock up, causing even more mayhem.

And I couldn’t check it. I still had to get the stern out to not hit the sailboat.

When it seemed, the bow would come out no more, I had to force myself to be slow and put her in idle, neutral, forward, power. Probably two to three seconds.

But remember at 2 feet per second forward due to current. In just doing that, reverse to forward, without slamming the damper plate, used half the distance between the two boats.

I stayed right behind the helm. I had to hope the line slipped off cleanly. As the solar panels were about two feet off the pilot house door, I swung the wheel hard right and goosed the power, to kick the stern out. The boat was still crabbing forward, so even with that maneuver, the stern only cleared by a few feet.

But she cleared. I hauled in the stern line quickly and turned on my driving lights to make sure I didn’t run over any sleeping sea otters.

01:28 Underway to Santa Cruz. I thanked every god I knew.

In hindsight, some thoughts:

  • It’s a no-brainer that I should have just swapped positions with one of the two sailboats. Either being in the front or end, would have been leaving no problem. Also, everyone at the YC was so accommodating, it would have been no problem.
  • Not as obvious is how the lack of a functional bow thruster affected this. It’s been three plus years now since by bow thruster stopped working. At least two times, we thought it was fixed, only to discover it wasn’t. But clearly, it hasn’t been a priority. Why?
    • Before it stopped working, there were two memorable times when I needed it, but winds and currents overwhelmed it. Thus, it has seemed better to just learn to live without than to depend on something that may not work as well as hoped in the worst conditions.
    • Be cause of that, I also stopped doing stuff because some marina or dock master suggested it. Now, I’ll say, “I don’t have a bow thruster, I can’t do that” Oh, no problem, we’ll put you on this “T” then! Duh!
    • And now this experience reinforces my feelings that at least for me, I’m better off without it. My first thought was if the bow thruster was working this would have been easy. And therein lies the problem. I would have pushed the bow out, jumped on board, used the bow thruster without the understanding that the boat was moving 2 feet a second and while the bow would have missed, the broad side of the boat would have slammed into the stern of the sailboat. No way was it going to get out of the way in the 10 seconds I had.
  • Yes, God certainly Watches Over Fools and Drunkards.

 

The Rest of the Story

Larry had returned to Alaska also, so when I got back to Dauntless on the 24th. I’d be taking her the last 400 miles of this 2000+ mile trip to Vallejo on my own. I had a plane ticket to leave Sacramento on 3 July to Austin.

My route thru Channel Isl Harbor

Assuming I had to arrive on the 2nd, I had 8 days to get to Vallejo. Ray, one of my boat mates in the new marina had kindly offered to give me a ride to the airport at 0h dark-30, so, I was back on the clock.

The first leg was critical, 70 nm to Point Conception. Winds had been light or southerly for two days, while I was in Salt Lake City, now, my day of departure, Monday they were forecast to increase from the west as the day progressed. (This is the way I use weather forecasts, looking at the trend, but not necessarily believing the specifics). 70 miles is 12 hours steaming time. I wanted to get around Point Conception before 16:00, otherwise as winds picked up on the bow, we would go slower and slower and I would become ever more miserable, yet again.

Therefore, I planned my departure from Kyoko’s dock at 04:00.

I never sleep well before embarking on any kind of trip, be it, by plane, train, automobile or boat. Thus, I was up just after 3 and figured I may as well get this show on the road.

I have a standard departure procedure. One that I adhere to since pulling away from the dock in the Chesapeake, 4 years ago, only to have the engine stop two minutes later from no fuel. At that time, I dropped the anchor in emergency mode (pulling the chain out of the wildcat and letting the anchor freefall) to stop our drift into nearby boats. Once that was done, I headed to the engine room to see what happened. A quick glance showed both fuel tank feeds were closed. Since I had just opened one, it was clear to me that in my mindset to “open” a closed valve, I had closed the one that was open. So much for check lists.

Getting Underway at 04:07

Way back then, I still did not have my auxiliary fuel pump installed, so of course it took 10 minutes of lift pump masturbation to get the air out and everyone happy again.

Consequently, I follow a standard start up routine, which consists of:

  • Engine room check, smelling and looking for obvious leaks and confirming fuel feed and Racor use.
  • Engine start
  • Turn on breakers for:
    • Running lights
    • VHF radio
    • Radar
    • Auto Pilot
    • “Loran” that’s the breaker used for my USB ports now
    • Horn
    • Check Anchor light is off
  • The boat computer, modems, router, Maretron system, two Samsung LCD displays are all 12 volt and on a separate breaker that is not on the pilot house system. They were already on, as that system takes a few minutes to boot up, as the router can be picky.

Now, on this night, I had already taken one spring line off before I went to sleep. In hindsight, that was probably a mistake, as it got me out of my routine.

Channel Isl Hbr overhead docking

03:30 I did my engine room check. I was also out of my routine because my engine room bilge pump was off and had been for the 10 days I was on this dock. With the little leak I had from the transmission, while no significant oil would be discharged, it would still make an embarrassing oil sheen, would not be nice for Kyoko and Mike, who had so graciously given me this spot. I could easily wait until we were off-shore.

03:43 Engine start. To this day, it is unclear to me what I was thinking. But I didn’t turn on the Auto Pilot or the Radar. More likely I did, but in any case, I untied from the dock, without realizing that neither was on.

03:52 Free from the dock and underway. I make the 90° turn to starboard to clear the dock, at which point I realize the Radar is not on. It’s dark. I don’t travel without the radar in the daytime, let alone now. But what to do.

These fairways were relatively wide, maybe 150 feet, but with boats and/or docks on either side. To return to Kyoko’s dock, I would have to do a 180° to port, then a 270° to dock bow facing out, as I was. In the dark, alone, that did not appeal to me. I also did not want to dock bow in, tie on the port side, as all my lines were on the stbd side. Again, being alone, limited my options. I decided to press on and look for a convenient place to stop to be bel to diagnose and solve the electrical issue.

In hindsight, I should have turned around and docked bow in. As it turned out, where I did decide to dock had a current that was vexing. At least this was a dock I knew. But at the time, I was more concerned about hitting something and felt it would be better someplace else. There must be some fuel dock or some such on the 40 minute it would take to go thru the channels and harbor to the sea.

My abrupt stop of video and boat for that matter is because while approaching the bridge, I was sure it was the same bridge I had come under two weeks earlier. But then, it that moment of panic, I thought maybe in the dark, I had made a wrong turn. I didn’t, but that’s what being in the dark will do for you. 

So, I slowed to inch under the bridge. I then proceeded to spend 15 minutes trying to back in a dock. With no current, it would have been easy, but in this case, there was a current, pushing the boat and especially the bow to port, so as I backed I’d end up almost perpendicular to the dock. After 3 or 4 attempts, I gave up and decided it would be easier to just go bow in around the corner. It was, and I did.

Coastal Explorer and Maretron data laving CI hbr

Just tied to midships. The boat secure, I was able to get under the helm to see why I had no power to the radar and autopilot.

Pilot house voltage has been an issue since day 1. I need to run a bigger or additional line and ground to the pilot house. When on long cruises, once the batteries are fully charged, the voltage at the batteries goes to 12.85v or thereabouts. The problem is that voltage in the pilot house is down to the low 12v. The Raymarine radar display will blink out momentarily when the voltage dips below 12. This usually happens when the auto pilot commands a longer turn. It gets annoying. So, since I never got around to running the additional wires, I instead did my normal half-assed fix of jumping from one buss to the other. The pilot house electrical panel has three separate busses. It used to be two, but sometime a couple years ago, I thought I had a fix for the radar by making a third buss. It sort of worked.

But coming north with Larry the radar display (not the transmitter or computer, only the display) started blinking again. I added another jumper. Worked great. But then upon arrival, I redid in a different way. Why? who knows!!

That different way is what was not working. I realized right away why the autopilot wasn’t getting power. So, I put it back the way it was, and all was good. That took 5 minutes. The additional docking took 45 minutes.

That delay would bite me in the ass later that afternoon.  Once I got out to sea, the winds were light from the south or southwest. I was headed 280°, just north of west. Winds out of the south were good, east better. Late in the morning the winds started to turn to 280° at 06 kts, right on the nose. 3 hours later at 14:00 they were 28012 g 15 kts, pitching had increased to 12° up and down and speed was reduced by one knot.

Underway again

I was able to make the turn to the NNW, 340° at 16:00. Winds had already increased to 290° 14 g 20. The turn took the winds and seas off the bow to the port forward quarter, much better than dead ahead. I was grateful for my early morning start.

The rest of the day was a piece of cake. Winds stayed 300° 15 g 20 for the rest of the evening. We were pitching and rolling, but it was tolerable. I didn’t jump overboard as I have been tempted to do when going into ahead sea.

And now you know the rest of the story.

Passing an Oil Platform south of Santa Barbara

I arrived in off Avila Beach in San Luis Obispo Bay around 22:00 and anchored that night using the radar. But then you already knew that.

Anchoring at Night

 

 

Time Waits for No One

I was on schedule, the one I’d made month’s earlier. It was June 10th.

So Calif from SD to Channel Islands The missing segment north of San Diego to Oceanside, is simply Garmim, being Garmin.

460 nm to go to our winter home of Vallejo, close compared to only a month ago, but now time was getting compressed. My hard, drop dead dates were also much closer.  July 6th was the hardest one, my flight from Austin Texas back to SGN, Saigon, HCMC, Vietnam.

Airline tickets can always be changed, but at a price and I was tired of just pissing money away.

CE chart off CA coast to Channel Islands Please don’t get confused. Channel Islands Harbor is NOT in the Channel Islands. But instead is just south of Oxnard on the mainland. That’s California just being California.

I also had a wedding in Salt Lake City June 23rd, that I really, really wanted to attend. Three years earlier, I’d crossed the stormy North Sea to get back to Ireland in time to meet my dear friend Jennifer, who was coming to Ireland just to see Dauntless. I’d known her since she was 8 years old. Now, she had met the love of her life and was getting married. I had to be there.

I also wanted, needed to go to Fairbanks, Alaska before I left the USA

I’d already arranged the marina for the winter, in Vallejo California.

It was simply going to be a busy month, but doable if the weather cooperated.

Entering Channel Islands harbor, which is NOT in the Channel Islands. But instead is just south of Oxnard on the mainland. That’s California just being California.

The most recent version of the plan had Dauntless and I getting to Vallejo by the 17th, flying to SLC on the 21st, then onto Fairbanks on the 25th, ending in Austin, Texas on the 3rd. I have good friends there and it so happens that the plane ticket to Vietnam is significantly cheaper if it starts in Austin (or other smaller markets) then NY or Detroit, even though my routing goes thru Detroit.

What are friends and family for? Friends and family are there to talk you out of stupid ideas or better said: to help you see the better plan.

Kyoko’s beautiful house in Channel Islands harbor

My friends, Mike and Adrianna, who now also have a Kadey Krogen 42, called While Knuckles, had suggested earlier that I stay in southern California longer. The reason I had resisted was that that plan upset my sense of completion: let’s get Dauntless settled, then travel.

The Pacific off the Southern California coast, south of Santa Barbara, has significantly better cruising weather. The winds are still predominately from the NW, but more like 50% of the time versus 90% further south. In addition, there are long periods of light & variable winds. Perfect cruising weather.

Dauntless from Kyoko’s house

And that’s what we had for the next five days.

Mike and Adrianna keep their boat in front of a friend house in Channel Islands harbor. They spoke to their friend, Kyoto, and she was happy to have my Kadey Krogen there, while White Knuckles was in Ensenada having some extensive upgrades taken care of.

The weather was also changing. It became clear that I would have to wait to do the last 270 miles from Point Conception to the Golden Gate and Vallejo. So, I took

Dauntless in front of Kyoko’s house

Mike and Kyoko up on their offer to keep Dauntless there as long as I needed, while I:

  1. Waited for weather
  2. Attended the wedding and
  3. Flew to Fairbanks and back
  4. Spent more money on tools and spares at Harbor Freight

I had to change one place ticket, but this was a much better plan. I was able to travel to the wedding and then Alaska knowing Dauntless was in good hands with sharp eyes watching out for her. I really appreciated the hospitality and it made for great 10 days

.

Harbor Freight is Wonderful

,

Dauntless Returns to the USA

Dauntless returned to the USA on June 9, 2018; four years after she left Cape Cod, Mass. I left with Julie and came back with Larry, an interesting swap. But it’s nice to share special moments with special people and I’ve known Larry since we met on T-3 in 1973.

CE chart of our arrival in San Diego

He’s good crew. He knows how to find the best ride for the conditions of wind and seas and he knows when to call me.

The check-in pier to the USA in San Diego is at the police dock at the entrance to the harbor. When we arrived at 19:00 there was a large fishing trawler occupying most of the dock. A spot on the Visitor’s Pier was open and I took it. Upon calling customs and Immigration, they told me everyone was busy with that fishing trawler, took my number and said they’d get back to me.

Noon , 6 hours from SD

Some minutes later, they did just that.  Telling me they were busy, they asked if we had Global Entry. We did, they took our passport numbers and welcomed us to the USA. After the nightmare of paperwork that the Caribbean is, I welcomed some common sense.

Larry and I celebrated our return by going to the typical restaurant & bar ubiquitous in the USA at upscale marinas and sea shores. We paid a lot for the crappiest meal we’d had in weeks. Welcome Home.

The Visitors Dock

It was 17 days from Cabo San Lucas to San Diego. I’ve written about most of the highlights or lowlights already. If you missed it, here are some links:

The Dingy Fiasco part 1

Third Time is the Charm; But it Wasn’t Easy

The Good, the Bad & the Ugly

Four Easy Days

The last 17 days saw us biding our time in anchorages, opposite, hot, dry, almost deserted towns, waiting for strong NW winds to subside so we could proceed NW in weaker NW winds.

Everything ended up working out so well thanks to generous friends and wonderful strangers.

Yet, I feel a disquiet that I hope is nothing more than the phase of the moon.